S1200 - S1299

we are working hard to document every message and error if any message is not described or the description is incomplete, contact us for more detailed information s1213 macro file not found, using default macro no macro file was found in the configuration directory, and the default macro will be used if a custom macro is supposed to be used, check if the file is in the correct directory this directory is under the installation directory in the config folder this directory can be changed with the docid\ mb7zdfnfetgk00uam dh setting s1214 creating file "\<macro file>" e ither the default macro cannot be found or the file could not be copied check if the file is protected or if the drive is full s1215 creating file "\<user macro file>" the default user macro could not be created check if the file is protected or if the drive is full s1216 unable to open file \<server config file> the server configuration file could not be opened to be written to check if the file is protected s1217 unable to open file \<server config file> the server configuration file could not be opened to be written to while trying to write the default configuration check if the file is protected s1218 configuration file not compatible the configuration files that are loaded were created with a version of the software that is not compatible this configuration is too old and cannot be automatically converted to this version s1219 invalid step frequency for cpu, default value used the step frequency stored in the configuration is not compatible with the connected controller make sure to set the step frequency only with a controller connected / not in simulation mode s1220 tan knife blend angle must be less than the value for the docid\ mb7zdfnfetgk00uam dh must be smaller than the docid\ mb7zdfnfetgk00uam dh s1221 too many axes for connected cpu this configuration was created for a controller with more axes than the current controller has the additional axes are disabled s1222 negative limit > positive limit the negative limit value for this axis is larger than the positive limit ensure the negative limit is always smaller than the positive limit s1223 tca negative limit > tca positive limit the negative limit for the tca is larger than the positive limit ensure the negative limit for x, y, and z is always smaller than the respective positive limit s1224 brake output cannot be inverted ensure that the io assigned to the brake output is not inverted because then the brake would never be engaged when the machine is powered off s1225 unable to write file \<service file name> the service configuration file could not be written check if the file is protected or if the drive is full s1226 unable to write file \<service file name> the service file that was just saved could not be parsed again this indicates that the new file is corrupt s1227 rename file \<service file name> failed the service config file could not be renamed; check if the file is protected s1228 unable to open file \<tools file name> the tool data file could not be opened to be written to while trying to save check if the file is protected s1229 unable to open file \<tools file name> the tool data file could not be opened to be written to while trying to write the default tool data check if the file is protected s1230 validating file \<variables file name> failed the variables file that was just saved could not be parsed again this indicates that the new file is corrupt the old version of the file is still intact and can still be used s1231 rename file \<variables file name> failed the temporary variables file could not be renamed; ensure that the file is not protected s1232 unable to open file \<variable file name> the variable file could not be opened to be written to while trying to save defaults check if the file is protected s1233 forward kin failed while trying to switch kin on the kinematics that are used are not able to resolve a cartesian position from the joint positions when using kinematic types distributed by edingcnc, contact us with a detailed description and a support archive when using custom kinematics, contact the supplier of them s1234 forward kin failed the kinematics that are used are not able to resolve a cartesian position from the joint positions when using kinematic types distributed by edingcnc, contact us with a detailed description and a support archive when using custom kinematics, contact the supplier of them s1236 disk full or write protected the default configuration file could not be written to the disk either the disk is full, or the file/folder is write protected s1237 disk full or write protected the configuration could not be read before this, the default configuration was written if none was present, so this indicates that either the disk is full or the file/folder is write protected s1238 disk full or write protected the configuration could not be read before this, the default configuration was written if none was present, so this indicates that either the disk is full or the file/folder is write protected s1239 disk full or write protected the default service configuration file could not be written to the disk either the disk is full or the file/folder is write protected s1240 disk full or write protected the service configuration could not be read before this, the default service configuration was written if none was present, so this indicates that either the disk is full or the file/folder is write protected s1241 disk full or write protected the default tool data file could not be written to the disk either the disk is full or the file/folder is write protected s1242 disk full or write protected the tool data could not be read before this, the default tool data file was written if none was present, so this indicates that either the disk is full or the file/folder is write protected s1243 disk full or write protected the default variable file could not be written to the disk either the disk is full or the file/folder is write protected s1244 disk full or write protected the variables could not be read before this, the default variable file was written if none was present, so this indicates that either the disk is full or the file/folder is write protected s1245 reset motion controller failed the system could not be reset the reason will have been displayed in a message before this one s1246 license expired, contact your supplier the license on this controller has an expiration date applied by the machine's manufacturer this expiration date has been exceeded, and the machine will not work anymore because of this contact your machine's manufacturer for a new code that will enable your machine again s1247 server priority not realtime the software tries to set the process to the highest priority possible in the os this message occurs when it is unable to set the priority to real time on windows this usually occurs when the application is not started with administrator rights s1248 please download correct firmware version the version of the firmware (software on the device) is not compatible with this software version the device's firmware can be updated by the user follow the steps outlined in docid\ pz3xehfi limmffti kyb to update this firmware s1249 controller is not enabled, please contact supplier the controller that is connected is not activated contact your controller supplier to find a resolution s1250 controller activation date expired, please contact supplier your machine's manufacturer has installed a date lock on the machine to continue operation, you must receive a new activation code from that manufacturer s1251 please download correct firmware version the version of the firmware (software on the device) is not compatible with this software version the device's firmware can be updated by the user follow the steps outlined in docid\ pz3xehfi limmffti kyb to update this firmware s1252 controller is not enabled, please contact supplier the controller that is connected is not activated contact your controller supplier to find a resolution s1253 controller activation date expired, please contact supplier your machine's manufacturer has installed a date lock on the machine to continue operation, you must receive a new activation code from that manufacturer s1254 please download correct firmware version the version of the firmware (software on the device) is not compatible with this software version the device's firmware can be updated by the user follow the steps outlined in docid\ pz3xehfi limmffti kyb to update this firmware s1255 controller is not enabled, please contact supplier the controller that is connected is not activated contact your controller supplier to find a resolution s1256 controller activation date expired, please contact supplier your machine's manufacturer has installed a date lock on the machine to continue operation, you must receive a new activation code from that manufacturer